P-0044

5V/5A 27W power supply with interchangeable plug standards

SKU: P-0044

Description

A power supply with interchangeable plug standards, supporting US, UK, EU, and AU standards. This product belongs to the 30W series, which does not mean it has a 30W power rating. Instead, it indicates a series of products with power ratings below 30W.

SPECIFICATION

• Type specification： P-0044-PD30W1C 5V5A/9V3A/12V2.25A/15V1.8A
• Scope: SMPS Adaptor(Wall mount) mechanical and environmental specifications of a SMPS, the power supplyprovides 27W continuous output power. The power supply shall meet the RoHS requirements

Input Characteristics

• Input Voltage & Frequency

specifications	Minimum	Rating	Maximum
Input Voltage	90Vac	100Vac~240Vac	264Vac
Input Frequency	47Hz	60Hz/50Hz	60Hz

• Inrush Current (cold start @ 120V AC)

No damage for 120V/50Hz at cold start (25℃)

• Average Efficiency

While input 110-240Vac ,the average efficiency is more than85.4% .The test point is at 25%,50%,75%and100%of max load respectively.

• Standby power

Standby power ≤1W @ 230VAC/50Hz.

• Cooling

Natural convection

• Mean Time Between Failure（MTBF）

The MTBF for the power adapter shall equal or exceed 10,000 hours when operated at full rated loadinanambienttemperature of 25 degree C.

• Output Characteristics

Item	Minimum	Nominal	Maximum
OUTPUT voltage Type-C	4.75V	5V	5.25V
	8.55V	9V	9.45V
	11.4V	12V	12.6V
	14.25V	15V	15.75V
Full-load current Type-C	PDO:5V5A/9V3A/12V2.25A/15V1.8A
Total power Type-C	27W
Fast charging protocol	Customized Protocol

Ripple & Noise: Tested by a oscilloscope using 20MHz bandwidth and the output is paralleled a 0.1uFceramiccapacitor and a 47uF electrolysis capacitor.

Protection Requirements

• Over Current Protection： OCP Point Limited: 110%-300% auto restart

The output shall hiccup when the over current applied to the output , and shall be self-recovery whenthefaultcondition is removed

• Short Circuit Protection

The input power shall decrease when the output is short to GND, the power supply shall not damage, andshallbeself-recovery when the fault condition is removed.

Environment Requirements

• Operating Temperature and Relative Humidity: 0℃ to +40℃ 20%RH to 80%RH @ Sea level shall below or no more than2000M
• Storage Temperature and Relative Humidity: -30℃ to +70℃ 10%RH to 90%RH（non-condensing）@ Sea level shall below 10000M
• Vibration: 10 to 300Hz sweep at a constant acceleration of 1.0G(Breadth: 3.5mm) for 1Hour for each of the perpendicularaxes X, Y, Z

EMC Standards & Safety Standards / EMC

• EMC Standards/EMC

EN 55022	EN 55022	CISPR 22	CISPR22
EN 61000-3-2	EN 61000-3-2	EN 61000-4-2	EN 61000-4-2
EN 61000-4-5	EN 61000-4-5	EN 61000-4-8	EN 61000-4-8
EN 61000-4-11	J55022

• Safety Standards

! Country	Type	Standard
ETL	USA	UL62368
GBR	UKCA-LVD	EN IEC 61558
CE	Europe	EN60950-1
Japan	PSE	J60950

• Ielectric Strength(Hi-pot): Primary to Secondary:3000Vac / 5mA / 60 seconds (3 seconds for production)
• Leakage Current: 0.25mA max. at 240Vac / 50Hz input
• Insulation Resistance: 100MΩ min. @ primary to secondary add a 500Vdc test voltage

Reliability Requirements

• Burn-in: The power supply shall be burn-in for 2 Hours under normal input and 80% rated load.

Testing Equipment

! NO.	Testing Equipment	Model	Remark
1	AC Source	Ainuo
2	ower Meter	8710C
3	Electronic Load	JT6330A
4	Oscilloscopes	MDO3014
5	Digital Multimeter	FLUKE 15B
6	DC Power	IT6721
7	HI-POT Tester	RK7122
8	Cons. T/H Simulator	XINBAO

Product Drawing

• AC Plug: UK/US/AU/EU removable plug
• DC Plug: Type-C
• DC Cable Spec: 3 wires, 18# x 2, 26# x 1, Type-C
• DC Cable Size: 1.2M

Gallery

• Product size

• EU Standard

• US Standard

• AU Standard

• UK Standard

Product Includes