Z-0144: Difference between revisions

From 52Pi Wiki
Jump to navigation Jump to search
(Created page with "==Raspberry Pi 3B Overlay Application Kit== This Kit contains a lot of new sensors such as chart below which can support DT (Device Tree) overlay modules in the newest operati...")
 
 
(7 intermediate revisions by the same user not shown)
Line 37: Line 37:
----
----
==Documentation:==
==Documentation:==
{| class="wikitable"
|-
! Id  !! Application Note !! Documentation
|-
| 1 || How to use 1 GPIO Pin to drive RaspberryPi Power-on-off-status light || [[File:1.How to use 1 GPIO Pin to drive RaspberryPi Power-on-off-status light.pdf]]
|-
| 2 || How to use 1 GPIO Pin to drive RaspberryPi Disk-Status light || [[File:2.How to use 1 GPIO Pin to drive RaspberryPi Disk-Status light.pdf]]
|-
| 3 || How to use VGA666 module to connect RaspberryPi  to display ||[[File:3.How to use VGA666 module to connect RaspberryPi to display.pdf ]]
|-
| 4 || How to use BMP180 Barometer to detect pressure ||[[File:4.How to use BMP180 Barometer to detect pressure.compressed.pdf]]
|-
| 5 || How to use IR device to remote control alarm buzzer ||[[File:5.How to use IR device to remote control alarm buzzer.pdf]]
|-
| 6 || How to use enc28j60 network interface card as a GPIO NIC ||[[File:6.How to use enc28j60 network interface card as a GPIO NIC.pdf]]
|-
| 7 || How to drive servo by using PCA9685 servo driver board || [[File:7.How to drive servo by using PCA9685 servo driver board.compressed.pdf]]
|-
| 8 || How to use RTC module to work as stable clock on RaspberryPi ||[[File:8.How to use RTC module to work as stable clock on RaspberryPi.pdf]]
|-
| 9 || How to use LM75 Thermometer module to detect the temperature in the room || [[File:9.How to use LM75 Thermometer module to detect the temperature in the room.pdf]]
|-
| 10 || How to use GPS module for real-time location and PPS clock synchronization service || [[File:10.How to use GPS module for real-time location and PPS clock synchronization service.compressed.pdf]]
|-
| 11 || How to use GPIO drive servo directly ||[[File:11.How to drive Servo directly by GPIO.compressed.pdf]]
|-
| 12 || How to use 0.96 Inch OLED Display to display system information ||[[File:12.How to use 0.96 Inch OLED Display to display system information.pdf]]
|-
| 13 || How to use DHT11 temperature sensor to detect the temperature in the room ||[[File:13.How to use DHT11 temperature sensor to detect the temperature in the room.pdf]]
|}
----

Latest revision as of 20:13, 27 August 2021

Raspberry Pi 3B Overlay Application Kit

This Kit contains a lot of new sensors such as chart below which can support DT (Device Tree) overlay modules in the newest operating system:

Id Product Name Quantity
1 IR receiver 1
2 IR sender 1
3 0.96-inch OLED display 1
4 9g Servo 2
5 VGA666 Module 1
6 PCA9685 Servo driver board 1
7 DHT11 temperature and humidity sensor 1
8 USB-GPS module (with wire) 1
9 Bmp180 barometer module 1
10 Breadboard (middle size) 1
11 Buzzer 1
12 RPI B+ T-Cobbler 1
13 GPIO Extend Board 1
14 Acrylic experimental platform (large) 1
15 Exquisite components box 1

Documentation:

Id Application Note Documentation
1 How to use 1 GPIO Pin to drive RaspberryPi Power-on-off-status light File:1.How to use 1 GPIO Pin to drive RaspberryPi Power-on-off-status light.pdf
2 How to use 1 GPIO Pin to drive RaspberryPi Disk-Status light File:2.How to use 1 GPIO Pin to drive RaspberryPi Disk-Status light.pdf
3 How to use VGA666 module to connect RaspberryPi to display File:3.How to use VGA666 module to connect RaspberryPi to display.pdf
4 How to use BMP180 Barometer to detect pressure File:4.How to use BMP180 Barometer to detect pressure.compressed.pdf
5 How to use IR device to remote control alarm buzzer File:5.How to use IR device to remote control alarm buzzer.pdf
6 How to use enc28j60 network interface card as a GPIO NIC File:6.How to use enc28j60 network interface card as a GPIO NIC.pdf
7 How to drive servo by using PCA9685 servo driver board File:7.How to drive servo by using PCA9685 servo driver board.compressed.pdf
8 How to use RTC module to work as stable clock on RaspberryPi File:8.How to use RTC module to work as stable clock on RaspberryPi.pdf
9 How to use LM75 Thermometer module to detect the temperature in the room File:9.How to use LM75 Thermometer module to detect the temperature in the room.pdf
10 How to use GPS module for real-time location and PPS clock synchronization service File:10.How to use GPS module for real-time location and PPS clock synchronization service.compressed.pdf
11 How to use GPIO drive servo directly File:11.How to drive Servo directly by GPIO.compressed.pdf
12 How to use 0.96 Inch OLED Display to display system information File:12.How to use 0.96 Inch OLED Display to display system information.pdf
13 How to use DHT11 temperature sensor to detect the temperature in the room File:13.How to use DHT11 temperature sensor to detect the temperature in the room.pdf