EP-0049: Difference between revisions
Jump to navigation
Jump to search
| Line 1: | Line 1: | ||
='''0.96 Inch OLED Module'''= | ='''0.96 Inch OLED Module'''= | ||
==Description== | ==Description== | ||
<pre> | |||
These displays are small, only about 1" diameter, but very readable due to the high contrast of an OLED display. | |||
This display is made of 128x64 individual yellow and blue OLED pixels, each one is turned on or off by the controller chip. | |||
Because the display makes its own light, no backlight is required. | |||
This reduces the power required to run the OLED. | |||
This breakout can be used with either an SPI interface | |||
The design is completely 3.3V-ready, with an onboard regulator and built in boost converter. | |||
The SSD1306 embeds with contrast control, display RAM and oscillator, which reduces the number of | The SSD1306 embeds with contrast control, display RAM and oscillator, which reduces the number of | ||
external components and power consumption. It has 256-step brightness control | external components and power consumption. | ||
It has 256-step brightness control. | |||
it supports Raspberry Pi A, A+,B,B+,2B,3B.</pre> | |||
it supports Raspberry Pi A, A+,B,B+,2B,3B. | |||
---- | ---- | ||
==Feature:== | ==Feature:== | ||
*Resolution: 128 x 64 dot matrix panel | *Resolution: 128 x 64 dot matrix panel | ||
Revision as of 18:07, 11 July 2016
0.96 Inch OLED Module
Description
These displays are small, only about 1" diameter, but very readable due to the high contrast of an OLED display. This display is made of 128x64 individual yellow and blue OLED pixels, each one is turned on or off by the controller chip. Because the display makes its own light, no backlight is required. This reduces the power required to run the OLED. This breakout can be used with either an SPI interface The design is completely 3.3V-ready, with an onboard regulator and built in boost converter. The SSD1306 embeds with contrast control, display RAM and oscillator, which reduces the number of external components and power consumption. It has 256-step brightness control. it supports Raspberry Pi A, A+,B,B+,2B,3B.
Feature:
- Resolution: 128 x 64 dot matrix panel
- Power supply
- VDD = 1.65V to 3.3V for IC logic
- VCC = 7V to 15V for Panel driving
- For matrix display
- OLED driving output voltage, 15V maximum
- Segment maximum source current: 100uA
- Common maximum sink current: 15mA
- 256 step contrast brightness current control
- Embedded 128 x 64 bit SRAM display buffer
- Pin selectable MCU Interfaces:
- 8-bit 6800/8080-series parallel interface
- 3 /4 wire Serial Peripheral Interface
- I2C Interface
- Screen saving continuous scrolling function in both horizontal and vertical direction
- RAM write synchronization signal
- Programmable Frame Rate and Multiplexing Ratio
- Row Re-mapping and Column Re-mapping
- On-Chip Oscillator
- Chip layout for COG & COF
- Wide range of operating temperature: -40°C to 85°C
Parameters:
- Dimensions: 36.36mm x 29.53mm x 10.01(include header)mm
- Weight without package: 7.15±2g
Package included:
1 x 0.96 Inch OLED Module
How to use
First of all, you should check the model of your Pi.
For Raspberry Pi A,A+,B,B+:
- First login, and download driver:
git clone https://github.com/hallard/ArduiPi_SSD1306
- Compile it and run:
cd ArduiPi_SSD1306/
sudo make
cd example/
sudo make
sudo ./oled_demo
For Raspberry Pi 2B, 3B:
- First login, and download driver:
git clone -b ArduiPi_OLED https://github.com/yoyojacky/libssd1306
- Compile it and run:
cd libssd1306/
sudo make
cd example/
sudo make
sudo ./oled_demo
FAQ
- Question:
- Answer:
Purchase Links
