D-0011: Difference between revisions

From 52Pi Wiki
Jump to navigation Jump to search
Line 24: Line 24:


==Specifications==
==Specifications==
* Stepper Motor Type: 28BYJ-48
* Driver Board: ULN2003AN
* A, B, C, D four-phase LED indicates the status of the stepper motor work.
* Stepper motor with a standard interface, when used directly pluggable.
* 5 line 4 phase can be used for ordinary ULN2003 chip driver, connect to the 2 phase , support the development board, with convenient use, direct docking.
* Rated Voltage: DC5V 4-phase
* Insulation Resistance: >10MΩ (500V)
* Dielectric Strength: 600V AC / 1mA / 1s
* Step angle: 5.625 x 1/64
* DC Resistance: 200Ω±7% (25C)
* Reduction ratio: 1/64
* Insulation Grade: A
* No-load Pull in Frequency: >600Hz
* No-load Pull out Frequency: >1000Hz
* Pull in Torque: >34.3mN.m(120Hz)
* Detent Torque: >34.3mN.m
* Temperature Rise: < 40K(120Hz)
==Gallery==
==Gallery==
==Package Includes==
==Package Includes==
==Documentations==
==Documentations==
==Keywords==
==Keywords==

Revision as of 14:08, 27 March 2020

Stepper Motor

Cl2.jpg

Description

A stepper motor, also known as step motor or stepping motor, is a brushless DC electric motor that divides a full rotation into a number of equal steps.
The motor's position can then be commanded to move and hold at one of these steps without any position sensor for feedback, as long as the motor is carefully sized to the application in respect to torque and speed.

Features

  • Small step angle
  • High positioning accuracy
  • High torque to inertia ratio
  • Stepping rate and accuracy

Small Step Angle

The angle by which the rotor of a stepper motor moves when one pulse is applied to the (input) stator is called step angle. This is expressed in degrees. The resolution of positioning of a stepper motor is decided by the step angle. Smaller the step angle the higher is the resolution of positioning of the motor. The step number of a motor is the number of steps it makes in one revolution. The stepper motors are realisable for very small step angle. Some precision motors can make 1000 steps in one revolution with a step angle of 0.36°. A standard motor will have a step angle of 1.8° with 200 steps for revolution. The step angles of 90°, 45°, 15° are not uncommon in simple motors.

High Positioning Accuracy

The quality of a stepper motor is decided by its positioning accuracy. This accuracy of positioning is a significant factor. In any application the stepper motors are expected to rotate by step angle when a pulse is given as input. It should come to rest in a precise position. Care must be exercised in the design and manufacture of a stepper motor as the accuracy at no load depends on the physical accuracy of the rotor and the stator. The positioning accuracy depends only on the machine characteristics and the driving circuit, while other electronic parameters have no effect on positioning accuracy. The stepper motors are designed to have very high restoring torque when the rotor is displaced following load torque.

High Torque-to-inertia Ratio

A stepper motor must move fast response to a pulse or a train of pulses. Fast response is also associated with quick start and quick stop of the motor. The motor must be capable of stopping at a position specified by the last pulse of the pulse train if the train is inhibited when the motor is running uniformly. A stepper motor must have a large ratio of torque to inertia.

Stepping Rate and Pulse Frequency

The speed of a stepper motor is indicated by the number of pulses per second. Stepping rate of the motor is therefore used to indicate the speed. As the motor moves by one step for a pulse the speed can also be indicated by pulses per second as pulse frequency. The absolute rotational speed and stepping rate are related by.

Specifications

  • Stepper Motor Type: 28BYJ-48
  • Driver Board: ULN2003AN
  • A, B, C, D four-phase LED indicates the status of the stepper motor work.
  • Stepper motor with a standard interface, when used directly pluggable.
  • 5 line 4 phase can be used for ordinary ULN2003 chip driver, connect to the 2 phase , support the development board, with convenient use, direct docking.
  • Rated Voltage: DC5V 4-phase
  • Insulation Resistance: >10MΩ (500V)
  • Dielectric Strength: 600V AC / 1mA / 1s
  • Step angle: 5.625 x 1/64
  • DC Resistance: 200Ω±7% (25C)
  • Reduction ratio: 1/64
  • Insulation Grade: A
  • No-load Pull in Frequency: >600Hz
  • No-load Pull out Frequency: >1000Hz
  • Pull in Torque: >34.3mN.m(120Hz)
  • Detent Torque: >34.3mN.m
  • Temperature Rise: < 40K(120Hz)

Gallery

Package Includes

Documentations

Keywords