|
|
| (22 intermediate revisions by the same user not shown) |
| Line 1: |
Line 1: |
| ==X200 EXPANSION BOARD==
| | |
| [[File:X200_860p.JPG|thumb|left|300px]]
| |
| <br style="clear:both;">
| |
| ----
| |
| {|-
| |
| |[[File:X200 165p1.JPG|left|]]
| |
| |[[File:X200 165p2.JPG|none]]
| |
| |[[File:X200 165p3.JPG|none]]
| |
| |[[File:X200 165p5.jpg|none]]
| |
| |[[File:X200 165p6.JPG|none]]
| |
| |}
| |
| <br style="clear:both;">
| |
| ----
| |
| ==KEY FEATURES==
| |
| {| class="wikitable"
| |
| |-
| |
| !Parameters !! Value
| |
| |-
| |
| |Input Voltage || 6V to 21Vdc converted to 5V, 3A via step-down DC/DC converter to power the Raspberry Pi
| |
| |-
| |
| |VGA output || HDMI to VGA converter supporting up to UXGA (1600×1200) and 1080p with 10-bit DAC
| |
| |-
| |
| |Audio || 3.5mm MIC in jack
| |
| - 3.5mm stereo audio jack
| |
| - SPDIF output
| |
| - Audio IO connector (Microphone input and stereo audio amplifier 3.3Wx2)
| |
| |-
| |
| |Wireless || WiFi (IEEE 802.11b/g/n) with external antenna
| |
| - IR sensor (38KHz)
| |
| |-
| |
| |USB Storage || Self-powered USB hub with 3 ports
| |
| |-
| |
| |Real-time clock (RTC) || Based on DS3231SN with included CR2032 battery
| |
| |-
| |
| |GPIO Control || 8-channel Darlington driver chip (ULN2803) allowing to control electronic circuits which require more current
| |
| |-
| |
| |Misc || Power output socket
| |
| - Camera flex slot so camera can still be used with the expansion board attached
| |
| - DIP switch to remove connection from RPi’s pin header
| |
| - Directly connected on top of the Raspberry Pi using the board GPIO header pins
| |
| - No wiring nor soldering is required
| |
| - Duplicated the 40-pin header of the R-Pi in order to support existing expansion boards
| |
| - Suitable for Raspberry Pi Model B+, Raspberry pi 2 Model B and Raspberry Pi 3 Model B NEW!
| |
| |-
| |
| |Dimensions || 85 x 56mm (Same size as Raspberry Pi)
| |
| |}
| |
| ----
| |
| ==PACKING LIST==
| |
| *1 x X200 expansion board
| |
| *1 x HDMI adapter
| |
| *1 x USB adapter
| |
| *1 x 2.4GHz WIFI antenna
| |
| *4 x nylon spacers (M3 x 20mm)
| |
| *8 x nylon screws (M3 x 6mm)
| |
| ----
| |
| ==QUICK START GUIDE==
| |
| A. Fitting the expansion board
| |
| B. Operation system
| |
| C. Power supply
| |
| D. HDMI to VGA converter
| |
| E. Microphone input and audio output
| |
| F. Audio input and output interface
| |
| G. Setting RTC time
| |
| H. Testing the IR reveiver
| |
| I. ULN2803 8-channel RC servo port
| |
| ----
| |
| ===A. FITTING THE EXPANSION BOARD===
| |
