X3000 SKU:EZ-0051: Difference between revisions

From 52Pi Wiki
Jump to navigation Jump to search
(Blanked the page)
Tag: Blanking
 
(One intermediate revision by the same user not shown)
Line 1: Line 1:
=X3000 Mini PC Kits =
 
{|-
|[[File:X3000 860p1.jpg|left|300px]]
|[[File:X3000 860p3.jpg|none|300px]]
|[[File:X3000 860p2.jpg|none|300px]]
|}
<br style="clear:both;">
----
==How to Mount it to TV==
[[File:X3000 860p10.jpg|none|300px]]
<br style="clear:both;">
----
==Tech Specs==
{| class="wikitable"
! Parameter!! Value
|-
|For Use With   || RASPBERRY PI 3 MODEL B / PI 2 MODEL B / PI 1 MODEL A+ / PI 1 MODEL B+
|-
|Operating System   || Raspbian Jessie / OSMC / Openelec / Volumio ...etc
|-
|Power Supply Unit   || AC 90 ~ 240V input, 5Vdc 3A output
    With 3 snap-in plugs for North America (US), Europe (EU), United Kingdom (UK)
|-
|I/O Ports  ||
  - USB 2.0 x4
  - Micro USB port  x1 (MSATA SSD external access with PC, MAC)
  - Mini HDMI
  - 10/100 Ethernet RJ45 jack
  - 3.5mm Audio jack ( HDMI audio output and  5.1CH SPDIF optical output)
  - MSATA port - Supports up to 1TB MSATA internal SSD
|-
|Wireless   ||  WIFI (IEEE 802.11b/g/n, Internal 2.4GHz antenna)
  - Built in IR sensor (38KHz, GPIO2 used)
|-
|Misc   ||
  - Turn on / off with 2-second touch
  - Colorful breathing light
  - Forced air cooling by built-in DC fan
  - Built in High quality audio headphone amplifier (TI TPA6133A)
|-
|Main Application Field ||
  - Home Theater Personal Computer(HTPC)
  - Education
  - Office 
  - Hotel Rooms. Diskless, locally run, smart design, upgrading hotel service
  - DIY a finished Raspberry Pi Computer
|}
----
[[File:X3000 860p4.jpg|left|300px]]
<br style="clear:both;">
*A. FITTING THE RASPBERRY PI
Required Accessories<br>
[[File:X3000 860p5.jpg|left|300px]]
<br style="clear:both;">
[[File:X3000 860p11.jpg|left|300px]]
<br style="clear:both;">
Accessories Installation <br>
[[File:X3000 860p6.jpg|left|300px]]
<br style="clear:both;">
[[File:X3000 860p7.jpg|left|300px]]
<br style="clear:both;">
----
==Raspberry Pi board Installation ==
*1) Remove the four screws at the bottom of the chassis and remove the bottom cover
[[File:X3000 860p18.jpg|left|300px]]
<br style="clear:both;">
[[File:X3000 860p8.jpg|left|300px]]
<br style="clear:both;">
MSATA SSD SHOULD BE INSTALLED BEFORE FITTING THE RASPBERRY PI. <br>
*2) Connect the power & IR cable from Raspberry Pi to the 2-pin male pin header
*3) Plugs the HDMI daughter board into the 14-pin HDMI female pin header
*4) Connect the cable of USB daughter board to the 3-pin PH connector
*5) Screwing the Raspberry Pi board
[[File:X3000 860p9.jpg|left|300px]]
<br style="clear:both;">
----
==B. POWER ON / OFF ==
<font color=red>TO TURN ON</font><br>
*1) HDMI cable and power adapter should be connected before powering on.
*2) Touch the power symbol and hold until the colorful breathing light is ON.
[[File:X3000 336p.jpg|left|300px]]
<br style="clear:both;">
----
<font color=red>TO SHUTDOWN</font><br>
*1) Power off your system using the system menu - IMPORTANT!
*2) Touch the power symbol and hold until the colorful breathing light is OFF.
*3) It is recommended to unplug the power supply unit when you are not using it.
<pre>
C1. OPERATING SYSTEM CONFIGURATION - OSMC  
C2. OPERATING SYSTEM CONFIGURATION - VOLUMIO
C3. OPERATING SYSTEM CONFIGURATION - RASPBIAN JESSIE
</pre>
*Based on RASPBIAN JESSIE
<pre>
Version: March 2016
Release date: 2016-03-18
Kernel version: 4.1
HDMI setting
</pre>
*<1> To ensure that the necessary kernel modules are loaded at boot
<code>pi@raspberrypi ~ $  sudo nano /boot/config.txt</code><br>   
*<2> Uncomment following three lines in config.txt by removing '#' located at start of the line. (check Images below)
[[File:Vga1.png|left|300px]]
<br style="clear:both;">
<pre>
hdmi_force_hotplug=1      pretends that HDMI device is always attached
hdmi_group                            specifies whether monitor is DMT type (Computers) or CEA type (TV)
hdmi_mode                            specifies the resolution of monitor.
</pre>
*<3> For hdmi_group value selection : If you’re using output as Computer monitor then replace value ’1′ with ’2′, so the new config will be like :
<pre>
hdmi_group=2
</pre>                     
(Select value 1 for TV, Select value 2 for monitor)<br>
*<4> For hdmi_mode value selection :  Now open eLinux RPi config scroll down, there in hdmi_mode two tables are given, select the correct resolution as per your monitor.
(Table1 if you’re using TV & Table2 if you’re using Monitor)<br>
Since my monitor’s resolution is 1440×900 px, hdmi_mode=47 fits me the best. So, the modified config.txt will be like.<br>
<pre>
hdmi_mode=47
</pre>
Overall my uncommented lines will look something like : <br>
[[File:Vga2.png|left|300px]]
<br style="clear:both;">
*<5> adding the "hdmi_drive=2" line at the bottom
[[File:Hdmi setting.png|left|300px]]
<br style="clear:both;">
*<6> Save your changes by pressing Ctrl-x then Y
*<7> Reboot your Raspberry Pi
<code>pi@raspberrypi ~ $  sudo reboot</code><br>
*<8> Mouse right click the speaker icon and select audio output of HDMI
[[File:X600 setting 1.png|left|300px]]
<br style="clear:both;">
*Testing the IR receiver
*<9> Installing LIRC
<code>pi@raspberrypi ~ $  sudo apt-get install lirc</code><br>
*<10> Add the two lines below to /etc/modules . This will start the modules up on boot. Pin 8 bellow will be used to take the output from the IR sensor.
<code>pi@raspberrypi ~ $  sudo nano /etc/modules</code><br>
<pre>   
lirc_dev
lirc_rpi gpio_in_pin=2
</pre>
[[File:Ir 0 - x3000 (1).png|left|300px]]
<br style="clear:both;">
*<11> Save your changes by pressing Ctrl-x then Y
*<12> If you are using 3.18.x RaspberryPi firmware you must modify one additional file for the lirc-rpi kernel extension to be loaded:       
Edit your /boot/config.txt file <br>
<code>pi@raspberrypi ~ $  sudo nano  /boot/config.txt</code><br>
and add:<br>
<code>dtoverlay=lirc-rpi,gpio_in_pin=2</code><br>
[[File:Ir 0 - x3000 (2).png|left|300px]]
<br style="clear:both;">
[[File:Ir2.gif|left|300px]]
<br style="clear:both;">

Latest revision as of 12:19, 4 August 2026

Retrieved from "https://wiki.52pi.com/index.php?title=X3000_SKU:EZ-0051&oldid=16529"