EZ-0076: Difference between revisions

From 52Pi Wiki
Jump to navigation Jump to search
m (Yoyojacky moved page X822 SKU: EZ-0076 to EZ-0076)
(Blanked the page)
Tag: Blanking
 
Line 1: Line 1:
==  X822 Dual 2.5" SATA HDD/SSD Shield==
[[ File:X822 280p1.jpg | right| 300px ]]
[[ File:X822 280p2.jpg | right| 300px ]]
[[ File:X822 280p3.jpg | right| 300px ]]


==Description==
X822 Dual 2.5" SATA HDD/SSD Shield is a Shield for Raspberry Pi to mount 2.5" SATA HDD/SSD.
* FOR USE WITH
<pre>Raspberry Pi 1 Model B+/ 2 Model B / 3 Model B / 3 Model B+</pre>
* OPERATING SYSTEM
<pre>All Raspberry Pi operating systems</pre>
==Features==
* Ideal storage solution for Raspberry Pi - Dual 2.5" SATA HDD/SSD Shield
* Supports up to 8TB 2.5-inch SATA hard disk drives (HDD) / solid-state drive (SSD)
* Supports 2 HDD or 2 SSD or HDD+SSD working at the same time
* Supports operating system installation and booting from your HDD/SSD
* Provides additional 2 USB ports for Raspberry Pi
* Powers the Raspberry Pi via on-board XH2.54 connector - Only one power adapter required
* Integrated USB 3.1 Gen1 to SATA 6Gb/s bridge controller
* Integrated USB 3.1 Gen 1 Hub Controller
* USB 2.0 connectivity offers plug-and-play functionality on your Raspberry Pi
* Quick file transfer with high-speed USB3.0 5Gb/s connectivity  from a PC or a Mac
* Specially-made USB3.0 jumper to connect with Raspberry Pi - no additional cables needed
* LED blue indicator indicates drive status
* Fully compatible with X735 for intelligent and safe power management
==Specification==
* Power supply: 5.1Vdc +/-5% , 4A
* DC jack: 5.5x2.5mm
* USB socket: USB 3.0 type A
* Power input / output connector : XH2.54 2-pin
* PCB Size: 107.5mm x 85mm
==Port Definitions==
[[File:X822 function description.jpg|left|800px]]
<br style="clear:both;">
==Note==
* For use with original power supply unit only
<font color=red>WARNING: Do not power your Raspberry Pi via the Pi's 40-pin header and micro-USB socket at the same time.</font><br>
==Package Include==
{| class="wikitable"
|-
! Product name !! Quantity
|-
|X822 HDD/SSD expansion board || 1
|-
|USB3.0 Jumper||1
|-
|USB 3.0 A-Male to A-Male Data cable || 1
|-
|2-Pin Power Connection Wire ||1
|-
|Spacer M/F M2.5 x 12mm || 4
|-
|Screw M2.5 x 6mm || 6
|-
|Screw M3 x 6mm || 4
|-
|Spacer F/F M2.5 x 15mm || 6
|}
==Optional Accessories==
===Power Supply Unit===
* AC 100 - 240V input 
* 5Vdc 4A output
* W/ EU and US plug
* 5.5*2.5 DC plug
* 1.2M cable w/ magnet ring
[[ File:PA 5V 4A 210p1.jpg|left|300px]]
<br style="clear:both;">
<pre> We are recommended you using this power adapter due to it can provide 5V/4A for your device.</pre>
==Galery==
{|
|[[File:X822 280p1.jpg|left|320px]]
|[[File:X822 280p2.jpg|none|320px]]
|[[File:X822 280p3.jpg|none|320px]]
|}
{|
|[[File:X822 280p4.jpg|left|320px]]
|[[File:X822 280p5.jpg|none|320px]]
|[[File:X822 280p6.jpg|none|320px]]
|}
==Installation Guide==
===Board Assembly===
<pre>Push a screw (M2.5*6mm) up through the arrowed mounting hole on the topside of X822 and screw down using a F/F spacer (M2.5*15mm) </pre>
[[File:X822 430p10.jpg|left|500px]]
<br style="clear:both;">
<pre>Push a screw (M2.5*6mm) up through the arrowed mounting hole on the underside of X822 and screw down using a F/F spacer (M2.5*12mm) </pre>
[[File:X822 430p6.jpg|left|500px]]
<br style="clear:both;">
<pre>Push a M/F spacer (M2.5*12mm) up through the arrowed mounting hole on the topside of X822 and screw down using a F/F spacer (M2.5*15mm)</pre>
[[File:X822 430p8.jpg|left|500px]]
<br style="clear:both;">
<pre>Insert your hard disk into the SATA socket. </pre>
[[File:X822 430p1.jpg|left|500px]]
<br style="clear:both;">
<pre>Use your thumb and forefinger of left hand to press the PCB and HDD hardly then screw down (M3*6mm screws). </pre>
[[File:X822 430p9.jpg|left|500px]]
<br style="clear:both;">
<pre>
a) Place your Raspberry Pi on top of X822 and screw down (M2.5*6mm screws)
b) Connect the 2-pin power cable from X822 to Raspberry Pi pin header - Pin 4 (5V, Read wire) and Pin 6 (Ground, Black wire).
c) Insert the USB3.0 jumper</pre>
[[File:X822 430p2.jpg|left|500px]]
<br style="clear:both;">
<pre>Optional -To use with X735 power management board
a) Unscrew 4 screws on the topside of Raspberry pi
b) Screw the M/F spacer (M2.5*12mm) down until it is hand tight
c) Plugs the X735 straight into your Raspberry Pi's GPIO header and screw down (M2.5*6mm screws)
d) Connect the 2-pin power connection wire from the 5V out connector on X735 to X822 2-pin power socket</pre>
<b><font color=red>Power adapter must be connected to the X735 only , not X822 and Raspberry Pi</font></b><br>
[[File:X822 430p3.jpg|left|500px]]
<br style="clear:both;">
==Booting from the X8 series storage board==
<B><font color=red>This tutorial explains how to boot your Raspberry Pi 3 from the X8 series (X820 V3.0, X850 V3.0, X822, X852, X860, X870) storage board</font></b>
===Program USB Boot Mode ===
Before a Raspberry Pi 3 will boot from the X8 series storage board, it needs to be booted from an SD card with a config option to enable USB boot mode. <br>
This will set a bit in the OTP (One Time Programmable) memory in the Raspberry Pi SoC that will enable booting from the X8 series storage board. <br>
Once this bit has been set, the SD card is no longer required. <br>
Note that any change you make to the OTP is permanent and cannot be undone.<br>
<br>
You can use any SD card running Raspbian or Raspbian Lite to program the OTP bit.<br>
If you don't have such an SD card then you can install Raspbian or Raspbian Lite in the normal way - see [ installing images | https://www.raspberrypi.org/documentation/installation/installing-images/README.md ]
First, prepare the<b> /boot </b>directory with up to date boot files:
<code>$ sudo apt-get update && sudo apt-get upgrade</code><br>
The above step is not required if you use the 2017-04-10 release of Raspbian / Raspbian Lite or later. <br>
===Then enable USB boot mode with this code: ===
<pre>echo program_usb_boot_mode=1 | sudo tee -a /boot/config.txt </pre><br>
This adds program_usb_boot_mode=1 to the end of /boot/config.txt.<br>
Reboot the Raspberry Pi with sudo reboot, then check that the OTP has been programmed with:
<pre>$ vcgencmd otp_dump | grep 17:</pre>
<b>17:3020000a</b><br>
Ensure the output 0x3020000a is shown. <br>
If it is not, then the OTP bit has not been successfully programmed. <br>
If you wish, you can remove the program_usb_boot_mode line from config.txt, so that if you put the SD card in another Raspberry Pi, it won't program USB boot mode.<br>
Make sure there is no blank line at the end of config.txt. <br>
You can edit config.txt using the nano editor using the command:<br>
<b>sudo nano /boot/config.txt </b>, for example.
===Prepare the operating system image ===
Starting with the 2017-04-10 release of Raspbian you can install a working Raspbian system to the X8 series storage board by copying the operating system image directly onto it, in the same way that you would for an SD card.<br>
To perform this step, follow the instructions here, remembering to select the drive that corresponds to your X8 series mass storage device. <br>
Once you have finished imaging your X8 series storage board,<br>
remove the USB data cable from your computer and insert the USB bridge into your Raspberry Pi and X8 series storage board USB ports. <br>
===Boot your Raspberry Pi 3 from the USB mass storage device ===
Powering it up. <br>
After between five and ten seconds the Raspberry Pi should begin booting, and display the rainbow splash screen on an attached screen. <br>
==FAQ==
* Q: Should I must change the boot sequence to my HDD/SSD ?
  A: No, it's all depends on you.
* Q: How to make a NAS storage from this product?
  A: 1. You need to part your partition by using fdisk command and make filesystem by using mkfs command, and create a directory and mount you disk on.
    2. install samba software by using apt-get install samba  and modify the configuration file /etc/samba/smb.conf and start the samba service.
==Keywords==
* X822, Dual 2.5" SATA HDD/SSD Shield, NAS, storage, Raspberry pi

Latest revision as of 12:18, 4 August 2026

Retrieved from "https://wiki.52pi.com/index.php?title=EZ-0076&oldid=16518"