EZ-0076 - Revision history

Yoyojacky: Blanked the page

2026-08-04T04:18:06Z

Blanked the page

2021-12-03T06:17:59Z

Yoyojacky moved page X822 SKU: EZ-0076 to EZ-0076

← Older revision	Revision as of 14:17, 3 December 2021
(No difference)

2019-08-06T05:10:20Z

FAQ

← Older revision		Revision as of 13:10, 6 August 2019
Line 150:		Line 150:

	==FAQ==		==FAQ==
	* A: Should I must change the boot sequence to my HDD/SSD ?		* Q: Should I must change the boot sequence to my HDD/SSD ?
	Q: No, it's all depends on you.		A: No, it's all depends on you.

	* A: How to make a NAS storage from this product?		* Q: How to make a NAS storage from this product?
	Q: 1. You need to part your partition by using fdisk command and make filesystem by using mkfs command, and create a directory and mount you disk on.		A: 1. You need to part your partition by using fdisk command and make filesystem by using mkfs command, and create a directory and mount you disk on.
	2. install samba software by using apt-get install samba and modify the configuration file /etc/samba/smb.conf and start the samba service.		2. install samba software by using apt-get install samba and modify the configuration file /etc/samba/smb.conf and start the samba service.

	==Keywords==		==Keywords==
	* X822, Dual 2.5" SATA HDD/SSD Shield, NAS, storage, Raspberry pi		* X822, Dual 2.5" SATA HDD/SSD Shield, NAS, storage, Raspberry pi

2019-08-06T05:10:02Z

FAQ

← Older revision		Revision as of 13:10, 6 August 2019
Line 151:		Line 151:
	==FAQ==		==FAQ==
	* A: Should I must change the boot sequence to my HDD/SSD ?		* A: Should I must change the boot sequence to my HDD/SSD ?
	* Q: No, it's all depends on you.		Q: No, it's all depends on you.

	* A: How to make a NAS storage from this product?		* A: How to make a NAS storage from this product?
	* Q: 1. You need to part your partition by using fdisk command and make filesystem by using mkfs command, and create a directory and mount you disk on.		Q: 1. You need to part your partition by using fdisk command and make filesystem by using mkfs command, and create a directory and mount you disk on.
	* 2. install samba software by using apt-get install samba and modify the configuration file /etc/samba/smb.conf and start the samba service.		2. install samba software by using apt-get install samba and modify the configuration file /etc/samba/smb.conf and start the samba service.

	==Keywords==		==Keywords==
	* X822, Dual 2.5" SATA HDD/SSD Shield, NAS, storage, Raspberry pi		* X822, Dual 2.5" SATA HDD/SSD Shield, NAS, storage, Raspberry pi

2019-06-11T08:25:37Z

Specification

← Older revision		Revision as of 16:25, 11 June 2019
Line 30:		Line 30:
	* Power input / output connector : XH2.54 2-pin		* Power input / output connector : XH2.54 2-pin
	* PCB Size: 107.5mm x 85mm		* PCB Size: 107.5mm x 85mm
			==Port Definitions==
			[[File:X822 function description.jpg\|left\|800px]]
			<br style="clear:both;">

	==Note==		==Note==
	* For use with original power supply unit only		* For use with original power supply unit only

2019-06-11T08:23:04Z

Board Assembly

@@ Line 80: / Line 80: @@
 ===Board Assembly===
 <pre>Push a screw (M2.5*6mm) up through the arrowed mounting hole on the topside of X822 and screw down using a F/F spacer (M2.5*15mm) </pre>
 [[File:X822 430p1.jpg|left|500px]]
 <br style="clear:both;">
 <pre>
+a) Place your Raspberry Pi on top of X822 and screw down (M2.5*6mm screws)
 ==Booting from the X8 series storage board==
 <B><font color=red>This tutorial explains how to boot your Raspberry Pi 3 from the X8 series (X820 V3.0, X850 V3.0, X822, X852, X860, X870) storage board</font></b>
@@ Line 110: / Line 134: @@
 Make sure there is no blank line at the end of config.txt. <br>
 You can edit config.txt using the nano editor using the command:<br>
 <b>sudo nano /boot/config.txt </b>, for example.
 ===Prepare the operating system image ===

2019-06-11T08:15:50Z

Booting from the X8 series storage board

← Older revision		Revision as of 16:15, 11 June 2019
Line 76:		Line 76:
	\|[[File:X822 280p6.jpg\|none\|320px]]		\|[[File:X822 280p6.jpg\|none\|320px]]
	\|}		\|}

			==Installation Guide==
			===Board Assembly===
			<pre>Push a screw (M2.56mm) up through the arrowed mounting hole on the topside of X822 and screw down using a F/F spacer (M2.515mm) </pre>
			[[File:X822 430p1.jpg\|left\|500px]]
			<br style="clear:both;">
			<pre>

	==Booting from the X8 series storage board==		==Booting from the X8 series storage board==

2019-06-11T03:48:14Z

Power Supply Unit

← Older revision		Revision as of 11:48, 11 June 2019
Line 61:		Line 61:
	* 5.5*2.5 DC plug		* 5.5*2.5 DC plug
	* 1.2M cable w/ magnet ring		* 1.2M cable w/ magnet ring
			[[ File:PA 5V 4A 210p1.jpg\|left\|300px]]
			<br style="clear:both;">
	<pre> We are recommended you using this power adapter due to it can provide 5V/4A for your device.</pre>		<pre> We are recommended you using this power adapter due to it can provide 5V/4A for your device.</pre>

2019-06-11T03:42:12Z

Galery

2019-06-11T03:41:42Z

X822 Dual 2.5" SATA HDD/SSD Shield