EP-0235 - Revision history

Yoyojacky: /* Keywords */

2025-10-27T03:01:15Z

Keywords

← Older revision		Revision as of 11:01, 27 October 2025
Line 147:		Line 147:

	Remember to replace placeholders with actual values relevant to your network configuration. Also, you might need to run `nmcli` commands with `sudo` if you require administrative privileges.		Remember to replace placeholders with actual values relevant to your network configuration. Also, you might need to run `nmcli` commands with `sudo` if you require administrative privileges.
			==3D print Case model file download==
			* 3D print case model file: [ https://print.deskpi.com/models/53 ]

	==Keywords==		==Keywords==
	* U2500 NVMe & Dual 2.5G ethernet for RPi5 expansion board, U2500, expansion board for RPi5, Raspberry Pi 5 hat expansion board with 2 gigabytes ethernet interface.		* U2500 NVMe & Dual 2.5G ethernet for RPi5 expansion board, U2500, expansion board for RPi5, Raspberry Pi 5 hat expansion board with 2 gigabytes ethernet interface.

Yoyojacky at 06:37, 1 July 2024

2024-07-01T06:37:32Z

← Older revision		Revision as of 14:37, 1 July 2024
Line 1:		Line 1:
	==~~U5000~~ M.2 NVME Dual USB3.0 to 2.5g Ethernet for Raspberry pi 5==		==U2500 M.2 NVME Dual USB3.0 to 2.5g Ethernet for Raspberry pi 5==
	[[File:EP-0235-01.jpg\|right\|320px]]		[[File:EP-0235-01.jpg\|right\|320px]]

	==Description==		==Description==
	The ~~U5000~~ M.2 NVMe & dual 2.5G ethernet for Raspberry Pi 5. The Raspberry Pi HAT (Hardware Attached on Top) board you have is a versatile expansion module designed to enhance the capabilities of your Raspberry Pi 5.		The U2500 M.2 NVMe & dual 2.5G ethernet for Raspberry Pi 5. The Raspberry Pi HAT (Hardware Attached on Top) board you have is a versatile expansion module designed to enhance the capabilities of your Raspberry Pi 5.

	==Features==		==Features==
Line 72:		Line 72:
	<br style="clear:both;">		<br style="clear:both;">
	==How to enable dual 2.5Gbps ethernet interface==		==How to enable dual 2.5Gbps ethernet interface==
	* Do remember connect the USB connector from ~~U5000~~ expansion board to Raspberry Pi 5 on USB3.0 Ports.		* Do remember connect the USB connector from U2500 expansion board to Raspberry Pi 5 on USB3.0 Ports.
	<pre>		<pre>
	sudo ifconfig		sudo ifconfig
Line 148:		Line 148:
	Remember to replace placeholders with actual values relevant to your network configuration. Also, you might need to run `nmcli` commands with `sudo` if you require administrative privileges.		Remember to replace placeholders with actual values relevant to your network configuration. Also, you might need to run `nmcli` commands with `sudo` if you require administrative privileges.
	==Keywords==		==Keywords==
	* ~~U5000~~ NVMe & Dual 2.5G ethernet for RPi5 expansion board, ~~U5000~~, expansion board for RPi5, Raspberry Pi 5 hat expansion board with 2 gigabytes ethernet interface.		* U2500 NVMe & Dual 2.5G ethernet for RPi5 expansion board, U2500, expansion board for RPi5, Raspberry Pi 5 hat expansion board with 2 gigabytes ethernet interface.

Yoyojacky: /* Package Includes */

2024-06-11T05:15:11Z

Package Includes

← Older revision		Revision as of 13:15, 11 June 2024
Line 147:		Line 147:

	Remember to replace placeholders with actual values relevant to your network configuration. Also, you might need to run `nmcli` commands with `sudo` if you require administrative privileges.		Remember to replace placeholders with actual values relevant to your network configuration. Also, you might need to run `nmcli` commands with `sudo` if you require administrative privileges.
	~~==Package Includes==~~
	~~[[File:EP-0235-清单.jpg\|left\|800px]]~~
	~~<br style="clear:both;">~~

	==Keywords==		==Keywords==
	* U5000 NVMe & Dual 2.5G ethernet for RPi5 expansion board, U5000, expansion board for RPi5, Raspberry Pi 5 hat expansion board with 2 gigabytes ethernet interface.		* U5000 NVMe & Dual 2.5G ethernet for RPi5 expansion board, U5000, expansion board for RPi5, Raspberry Pi 5 hat expansion board with 2 gigabytes ethernet interface.

Yoyojacky: /* Package Includes */

2024-06-11T05:14:48Z

Package Includes

← Older revision		Revision as of 13:14, 11 June 2024
Line 148:		Line 148:
	Remember to replace placeholders with actual values relevant to your network configuration. Also, you might need to run `nmcli` commands with `sudo` if you require administrative privileges.		Remember to replace placeholders with actual values relevant to your network configuration. Also, you might need to run `nmcli` commands with `sudo` if you require administrative privileges.
	==Package Includes==		==Package Includes==
	*		[[File:EP-0235-清单.jpg\|left\|800px]]
	*		<br style="clear:both;">
	*
	==Keywords==		==Keywords==
	* U5000 NVMe & Dual 2.5G ethernet for RPi5 expansion board, U5000, expansion board for RPi5, Raspberry Pi 5 hat expansion board with 2 gigabytes ethernet interface.		* U5000 NVMe & Dual 2.5G ethernet for RPi5 expansion board, U5000, expansion board for RPi5, Raspberry Pi 5 hat expansion board with 2 gigabytes ethernet interface.

Yoyojacky: /* Gallery */

2024-06-11T04:59:42Z

Gallery

@@ Line 25: / Line 25: @@
 * Dual USB port connector
 ==Gallery==
-TBD.
+* Product outlook
+[[File:EP-0235-01.jpg|left|800px]]
 ==How to enable PCIe on Raspberry Pi 5==
 * We assume that you are using Raspberry Pi OS (bookworm) 2024-03-15

Yoyojacky: /* U5000 M.2 NVME Dual USB3.0 to 2.5g Ethernet for Raspberry pi 5 */

2024-06-11T04:54:19Z

U5000 M.2 NVME Dual USB3.0 to 2.5g Ethernet for Raspberry pi 5

← Older revision		Revision as of 12:54, 11 June 2024
Line 1:		Line 1:
	==U5000 M.2 NVME Dual USB3.0 to 2.5g Ethernet for Raspberry pi 5==		==U5000 M.2 NVME Dual USB3.0 to 2.5g Ethernet for Raspberry pi 5==
			[[File:EP-0235-01.jpg\|right\|320px]]

	==Description==		==Description==
	The U5000 M.2 NVMe & dual 2.5G ethernet for Raspberry Pi 5. The Raspberry Pi HAT (Hardware Attached on Top) board you have is a versatile expansion module designed to enhance the capabilities of your Raspberry Pi 5.		The U5000 M.2 NVMe & dual 2.5G ethernet for Raspberry Pi 5. The Raspberry Pi HAT (Hardware Attached on Top) board you have is a versatile expansion module designed to enhance the capabilities of your Raspberry Pi 5.

Yoyojacky at 07:29, 30 May 2024

2024-05-30T07:29:26Z

← Older revision		Revision as of 15:29, 30 May 2024
Line 115:		Line 115:

	Remember to replace placeholders with actual values relevant to your network configuration. Also, you might need to run `nmcli` commands with `sudo` if you require administrative privileges.		Remember to replace placeholders with actual values relevant to your network configuration. Also, you might need to run `nmcli` commands with `sudo` if you require administrative privileges.
			==Package Includes==
			*
			*
			*
			==Keywords==
			* U5000 NVMe & Dual 2.5G ethernet for RPi5 expansion board, U5000, expansion board for RPi5, Raspberry Pi 5 hat expansion board with 2 gigabytes ethernet interface.

Yoyojacky at 07:27, 30 May 2024

2024-05-30T07:27:40Z

← Older revision		Revision as of 15:27, 30 May 2024
Line 22:		Line 22:
	* Support PCIex1		* Support PCIex1
	* Dual USB port connector		* Dual USB port connector
			==Gallery==
			TBD.

			==How to enable PCIe on Raspberry Pi 5==
			* We assume that you are using Raspberry Pi OS (bookworm) 2024-03-15
			* Enable PCIe function
			Edit /boot/firmware/config.txt file and adding following parameter in to the file.
			<pre>
			dtparam=pciex1
			dtparam=pciex1_gen=3
			</pre>
			[[File:Config.txt file.png\|left\|800px]]
			<br style="clear:both;">
			Save it and then do remember reboot your Raspberry Pi to take effect.
			Following figure shows that the speed of transport on NVMe SSD and booting from nvme device.
			[[File:Nvme speed U5000.png\|left\|800px]]
			<br style="clear:both;">
			==How to enable dual 2.5Gbps ethernet interface==
			* Do remember connect the USB connector from U5000 expansion board to Raspberry Pi 5 on USB3.0 Ports.
			<pre>
			sudo ifconfig
			</pre>
			Result be like:
			[[File:Dual ethernet interfaces.png\|left\|800px]]
			<br style="clear:both;">
			Then you can use `nmcli` command to configure network connection.
			[[File:Nmcli show.png\|left\|800px]]
			<br style="clear:both;">
			Here's a step-by-step guide on how to configure a network interface using `nmcli`, the command-line client for NetworkManager:

			===1. Check Network Interfaces===
			First, you need to identify the network interfaces available on your system. Use the following command to list all network interfaces:
			<pre>
			nmcli device status
			</pre>

			===2. Connect to a Network:===
			To connect to a wired or wireless network, you can use the `nmcli` command with the `d` (device) and `connect` options:
			<pre>
			nmcli d connect [interface-name]
			</pre>
			Replace `[interface-name]` with the name of your network interface.

			===3. Set a Static IP Address:===
			If you want to set a static IP address for a wired connection, use the following command:
			<pre>
			nmcli con mod [connection-name] ipv4.addresses [ip-address]/[subnet-mask]
			nmcli con mod [connection-name] ipv4.gateway [gateway-address]
			nmcli con mod [connection-name] ipv4.dns "[dns1],[dns2]"
			nmcli con mod [connection-name] ipv4.method manual
			</pre>
			Replace `[connection-name]` with the name of your connection, `[ip-address]` with your desired IP address, `[subnet-mask]` with the subnet mask, `[gateway-address]` with the default gateway, and `[dns1],[dns2]` with your DNS servers.

			===4. Set a Static IP Address for Wireless:===
			For a wireless connection, you'll need to create a new connection profile:
			<pre>
			nmcli con add type wifi con-name [connection-name] ifname [interface-name] ssid [ssid] mode [mode] ssid-type [type]
			</pre>
			Replace `[connection-name]` with a name for your connection, `[interface-name]` with the wireless interface name, `[ssid]` with the network's SSID, `[mode]` with the mode (usually `infrastructure`), and `[type]` with the SSID type (usually `ap`.

			Then set the static IP details:
			<pre>
			nmcli con mod [connection-name] ipv4.addresses [ip-address]/[subnet-mask]
			nmcli con mod [connection-name] ipv4.gateway [gateway-address]
			nmcli con mod [connection-name] ipv4.dns "[dns1],[dns2]"
			nmcli con mod [connection-name] ipv4.method manual
			</pre>

			===5. Bring Up the Interface:===
			Once you've configured the interface, you can bring it up using the following command:
			<pre>
			nmcli con up [connection-name]
			</pre>

			===6. Bring Down the Interface:===
			If you need to bring down the interface, use the following command:
			<pre>
			nmcli con down [connection-name]
			</pre>

			===7. Check Connection Status:===
			To check the status of your connection, use:
			<pre>
			nmcli con show [connection-name]
			</pre>

			===8. Delete a Connection :===
			If you need to delete a connection profile, you can do so with:
			<pre>
			nmcli con del [connection-name]
			</pre>

			Remember to replace placeholders with actual values relevant to your network configuration. Also, you might need to run `nmcli` commands with `sudo` if you require administrative privileges.

Yoyojacky: /* Features */

2024-05-30T07:06:16Z

Features

← Older revision		Revision as of 15:06, 30 May 2024
Line 12:		Line 12:
	* <strong>Compact and Integrated Design</strong> The board is designed to be compact and integrate seamlessly with the Raspberry Pi, providing a clean and efficient setup without the need for additional cables or adapters.		* <strong>Compact and Integrated Design</strong> The board is designed to be compact and integrate seamlessly with the Raspberry Pi, providing a clean and efficient setup without the need for additional cables or adapters.

	* <strong>Enhanced Functionality</strong>By combining high-speed storage and network capabilities, this HAT board significantly enhances the functionality of a Raspberry Pi, making it suitable for a wide range of applications that require both storage and network performance.		* <strong>Enhanced Functionality</strong> By combining high-speed storage and network capabilities, this HAT board significantly enhances the functionality of a Raspberry Pi, making it suitable for a wide range of applications that require both storage and network performance.

	This HAT board is an excellent addition to any Raspberry Pi setup, offering a convenient way to boost both storage and networking capabilities in a single, compact package.		This HAT board is an excellent addition to any Raspberry Pi setup, offering a convenient way to boost both storage and networking capabilities in a single, compact package.

Yoyojacky: /* Features */

2024-05-30T07:05:54Z

Features

← Older revision		Revision as of 15:05, 30 May 2024
Line 4:		Line 4:

	==Features==		==Features==
	* <strong>PCIe Interface Support**: It includes a single PCIe (Peripheral Component Interconnect Express) interface that can be used to expand the system with an M.2 NVMe SSD. This allows for high-speed storage solutions that are compatible with the 2230 and 2242 form factors.		* <strong>PCIe Interface Support</strong> It includes a single PCIe (Peripheral Component Interconnect Express) interface that can be used to expand the system with an M.2 NVMe SSD. This allows for high-speed storage solutions that are compatible with the 2230 and 2242 form factors.

	* <strong>M.2 NVMe SSD Support</strong> The HAT board supports M.2 NVMe Solid State Drives, which are known for their high-speed data transfer rates and low latency. This is particularly useful for applications that require fast access to data, such as databases, media servers, and high-performance computing tasks.		* <strong>M.2 NVMe SSD Support</strong> The HAT board supports M.2 NVMe Solid State Drives, which are known for their high-speed data transfer rates and low latency. This is particularly useful for applications that require fast access to data, such as databases, media servers, and high-performance computing tasks.