EP-0104 - Revision history

Yoyojacky: /* Features */

2024-04-16T03:17:51Z

Features

← Older revision		Revision as of 11:17, 16 April 2024
Line 19:		Line 19:
	* DockerPi Series		* DockerPi Series
	* SMPS		* SMPS
	* 12V DC Input		* 12V DC Input Inner diameter: 6.32mm x 2.1mm （ Adaptation interface: 5.5mmx2.1mm DC power cord）
	* Typical output:20W(5V/4A)		* Typical output:20W(5V/4A)
	* Absolute output:25W(5V/5A)		* Absolute output:25W(5V/5A)

2021-08-27T10:25:02Z

← Older revision	Revision as of 18:25, 27 August 2021
(No difference)

2021-06-17T07:47:17Z

One-Step Automated Install(Raspberry Pi)

← Older revision		Revision as of 15:47, 17 June 2021
Line 85:		Line 85:

	'''<font color=red>NOTE:The LED status is incorrect until the drive is installed successfully!</font>'''		'''<font color=red>NOTE:The LED status is incorrect until the drive is installed successfully!</font>'''
			===More information===
			* Please refer to github URL: [ https://github.com/geeekpi/dockerpi ]

	==FAQ==		==FAQ==

2021-06-17T07:45:52Z

One-Step Automated Install(Raspberry Pi)

← Older revision		Revision as of 15:45, 17 June 2021
Line 80:		Line 80:
	<STRIKE> wget -qO- https://git.io/fj3b9 \| sudo bash </STRIKE>		<STRIKE> wget -qO- https://git.io/fj3b9 \| sudo bash </STRIKE>
	<pre>		<pre>
	https://raw.githubusercontent.com/geeekpi/dockerpi/master/powerboard/install.sh		https://raw.githubusercontent.com/geeekpi/dockerpi/master/powerboard/install.sh \| sudo bash
	</pre>		</pre>
	Reboot your Raspberry Pi and finish installation.		Reboot your Raspberry Pi and finish installation.

2021-06-17T07:45:36Z

One-Step Automated Install(Raspberry Pi)

← Older revision		Revision as of 15:45, 17 June 2021
Line 77:		Line 77:

	==One-Step Automated Install(Raspberry Pi)==		==One-Step Automated Install(Raspberry Pi)==
			* Due to short link is not available, please use github to install driver.
			<STRIKE> wget -qO- https://git.io/fj3b9 \| sudo bash </STRIKE>
	<pre>		<pre>
	~~wget -qO-~~ https://~~git~~.io/~~fj3b9 \| sudo bash~~		https://raw.githubusercontent.com/geeekpi/dockerpi/master/powerboard/install.sh
	</pre>		</pre>
	Reboot your Raspberry Pi and finish installation.		Reboot your Raspberry Pi and finish installation.

2020-09-01T03:42:17Z

Power Board Details

← Older revision		Revision as of 11:42, 1 September 2020
Line 64:		Line 64:

	==Power Board Details==		==Power Board Details==
	* ~~It only uses~~ the ~~I2C function~~ of the ~~GPIO~~ pins~~, so all GPIOs can be used without occupying~~ the ~~GPIO pins~~.		* The module does not occupy any GPIO pins, but provides power to the 5V and GND of the Raspberry Pi through the 5V and GND pins of the power board.
	[[File:Powerboard info.jpg\|left\|500px]]		[[File:Powerboard info.jpg\|left\|500px]]
	<br style="clear:both;">		<br style="clear:both;">

2020-09-01T03:42:01Z

Description

← Older revision		Revision as of 11:42, 1 September 2020
Line 11:		Line 11:

	DockerPi PowerBoard recommends 12V 2A or above power input and 12V power from 4-pin headers to other DockerPi. (If other modules require 12V power)		DockerPi PowerBoard recommends 12V 2A or above power input and 12V power from 4-pin headers to other DockerPi. (If other modules require 12V power)


	'''Note: DockerPi PowerBoard does not support hot plug.		'''Note: DockerPi PowerBoard does not support hot plug.

2020-09-01T03:38:42Z

Power Board Details

← Older revision		Revision as of 11:38, 1 September 2020
Line 63:		Line 63:

	==Power Board Details==		==Power Board Details==
			* It only uses the I2C function of the GPIO pins, so all GPIOs can be used without occupying the GPIO pins.
	[[File:Powerboard info.jpg\|left\|500px]]		[[File:Powerboard info.jpg\|left\|500px]]
	<br style="clear:both;">		<br style="clear:both;">

	==Mechanical Drawing==		==Mechanical Drawing==
	[[File:Powerboard mech.png\|left\|500px]]		[[File:Powerboard mech.png\|left\|500px]]

2019-09-18T03:37:12Z

FAQ

← Older revision		Revision as of 11:37, 18 September 2019
Line 114:		Line 114:
	* Q: Could i control the speed of fan?		* Q: Could i control the speed of fan?
	A: No.		A: No.
			* Q: Can I use car battery power directly to board without step down?
			A: Yes, we suggest that you make sure the car batteries can offer 12V /3A for Raspberry Pi and external deivces,and the input voltage is lower than 17V.

	==Keywords==		==Keywords==
	* DockerPi,Power,5V4A,Hat,Stack		* DockerPi,Power,5V4A,Hat,Stack

2019-09-03T03:57:31Z

FAQ

← Older revision		Revision as of 11:57, 3 September 2019
Line 83:		Line 83:
	==FAQ==		==FAQ==
	* Q: Why i have bought the DockerPi PowerBoard,i still need to buy the power supply?		* Q: Why i have bought the DockerPi PowerBoard,i still need to buy the power supply?
	A: ~~Because~~ the DockerPi ~~PowerBoard recommands 12V/2A Power supply or above input~~.~~If you have this type of~~ power supply,~~you don't have~~ to ~~buy it~~.		A: Powboard's function is to allow you to use an external DC power supply greater than 5V and less than 16V, which not only ensures that the raspberry pie uses electricity normally, but also ensures that when the raspberry pie uses
			high-power additional equipment, the system will not be unstable due to feeding.In addition, POWERBOARD is a dockerpi series product, which provides effective power support for DockerPi follow-up products. When POWERBOARD is used
			for power supply, raspberry pie does not need to be connected to 5V power supply.
	* Q: Can I stack multiple power expansion boards?		* Q: Can I stack multiple power expansion boards?
	A: No.		A: No.