Raspberry Pi night vision camera adjustable-focus module ER-0016

From 52Pi Wiki
Jump to navigation Jump to search

Raspberry Pi night vision camera adjustable-focus module[edit]

ER 00161 1.jpg

This is a raspberry pie camera that supports night vision and focus adjustment.
It is connected to the Raspberry Pi through the CSI interface.
It is usually used as a night surveillance camera or anti-theft surveillance camera.
Many fans use it to DIY their own project.
The night photography project, the principle is that the night vision surveillance camera generally uses an infrared night vision camera.
The working principle is that in the dark environment without visible light or low light,
the infrared light emitting device actively projects the infrared light onto the object,
and the infrared light is reflected by the object. Enter the lens for imaging.

Features[edit]

  • Raspberry Pi Camera Module
  • Supports Night Vision
  • Adjustable-Focus
  • Supports all revisions of the Pi
  • 5 megapixel OV5647 sensor
  • Detachable infrared night vision
  • Sensor best resolution : 1080p
  • Video Mode: 1080p30, 720p60 and 640 × 480p60/90
  • Linux integration: V4L2 driver available
  • CMOS size: 1/4 inch
  • Aperture (F): 1.8
  • Focal length: 3.6mm
  • Diagonal : 75.7 degree
  • 4 screw holes
  • Support 3.3v output
  • Support access to fill light or infrared light
  • Size: 25mm * 24mm
  • Weight: 0.030kg

Gallery[edit]

ER 00161 2.jpg
ER 00161 4.jpg
ER 00161 5.jpg

Notes[edit]

The LED fill lights on both sides will warm up(generally in 40 to 50℃) when they working, 
but it is normal, please don't worry, they can keep working 24 hours aday, it will not damage the camera normally. 
You can adjust the micro adjustable resistor(beside the lights) to turned down the lights to Lower temperatures. 

Package Includes[edit]

  • 1x 5M OV5647 Camera
  • 2x infrared light sensor
  • 1x Supersmooth cleaning fiber
  • 5x infrared light sensor fixed screws and nuts
  • 1x Camera Fiber Cable for Raspberry Pi 2B/3B/3B+/3A+
  • 1x Camera Fiber Cable for Raspberry Pi zero/zero w
  • 1x Stick tape
  • 1x Instruction
ER 00161 4.jpg
ER 00161 6.jpg


Dimension Information[edit]

ER 00161 3.jpg

How to Use the camera[edit]

  • 1. Connect the Camera
 The flex cable inserts into the connector situated between the Ethernet and HDMI ports, with the
silver connectors facing the HDMI port. The flex cable connector should be opened by pulling the tabs
on the top of the connector upwards then towards the Ethernet port. The flex cable should be
inserted firmly into the connector, with care taken not to bend the flex at too acute an angle. The top
part of the connector should then be pushed towards the HDMI connector and down, while the flex
cable is held in place.
ER 00161 1.jpg


  • 2. Enable it on Raspbian

Open the raspi-config tool from the Terminal

 sudo raspi-config 

Navigate the Cursor to Interfacing Options and then select camera and enable it. Reboot your Pi after setting.

  • 3. Taking Photo:
 sudo raspistill -o image.jpg 
  • 4. Shooting Video:
 sudo raspivid -t 20000 -o video.h264 

-t means it will last for 20s, -o means "OUTPUT file"
More info please using:

 raspistill -h 
 raspivid -h 

More information[edit]

[ getting-started-with-picamera | https://projects.raspberrypi.org/en/projects/getting-started-with-picamera ]

Keywords[edit]

Raspberry pi 3B+ Camera, Raspberry Pi 2B Camera, Raspberry Pi 3A+ Camera, Raspberry Pi Zero camera, Raspberry Pi Zero W camera, official Camera, taking picture, picamera, raspivid, raspistill, ov5647 ,CMOS, infrared light ,sensor , night vision camera, night vision, adjustable-focus, raspicam, raspberry camera module

Trouble shooting[edit]

  • 1.Check the flex cable, Does it loose?
  • 2.Please make sure the flex cable is correct.
  • 3.Please make sure you have already enabled the "camera" on your Raspberry Pi via using "sudo raspi-config" command.