Rack Tower SKU: ZP-0088

From 52Pi Wiki
Jump to navigation Jump to search

Rack Tower

Sc0 00.jpg

Description

Rack Tower stands for a new concept for the 4-layer acrylic case for cluster.
This 4-layer acrylic oversized fan enclosure is a new product designed to provide shell protection and cooling solutions for Raspberry Pi clusters, Raspberry Pi NAS servers, Jetson Nano clusters, and disk array clusters.
It is very delicate. The long fixing screws are designed with flat head screws, smooth and easy to install.
The fool-proof design of the positioning holes can prevent you from having trouble during installation.
A variety of screws with different specifications can meet your various product fixing needs.
For example, Raspberry Pi, 2.5-inch hard drive, 3.5-inch hard drive, Jetson Nano and so on.
In addition, the large fan is driven by 5V, which can be directly powered by the Raspberry Pi, and it will have a colorful halo when it is running, which is very cool.

Features

  • Easy to assemble
  • Colorful LED Huge Fan
  • Compatible with Raspberry Pi, 2.5MM HDD, Jetson Nano
  • Extramly heat dissipation effect
  • Crystal Hander easy to carry on
  • Flexible Mounting position
If you want to make better use of space, you can place the Raspberry Pi on one side of the bracket, and on the right side, you can place other small equipment, such as UPS power, etc., and it can also be used as a place for cables.

Gallery

Sc0 01.jpg
Sc0 3.jpg
Scrack1.jpg

Scrack2.jpg
Scrack3.jpg
Scrack4.jpg

Scrack5.jpg
Scrack6.jpg
Sc7 2.jpg

Application Scenario

Scrack11.jpg
Scrack12.jpg
Scrack14.jpg
Scrack8.jpg
Scrack9.jpg

Package Includes

  • One set of acrylic case.
    • 1 x Right baffle
    • 1 x Left baffle
    • 4 x Middle interlayer
    • 2 x Fan bracket
    • 1 x 125mm Acrylic cylinder
  • 4 x 130mm Male and female rivet
  • 2 x M3x8mm Screw (for handle)
  • 1 x 120mm RGB LED 5V fan
  • 4 x M3x30mm screw (for 120mm Fan)
  • 4 x M3 nut (for 120mm fan)
  • 17 x M2.5x5+6mm copper column(for RPi)
  • 17 x M2.5 nut (for middle interlayer)
  • 16 x M3x5 wide head screw(for 4 hard disks)
  • 1 x Long transparent screwdriver
  • 1 x Installation instructions
  • 4 x Heat sink Kit for Raspberry Pi 4B
  • 4 x Heat sink Kit for Raspberry Pi 3B
Scrack10.jpg


How to Assemble

Please read this guide carefully before you starting assemble.
  • Step 1. Fixed the copper sticks to acrylic layer after peeling off the protection film.
Anz1.jpg


  • Step 2. Paste heat sinks to Raspberry Pi and fix the raspberry pi to the acrylic layer with M2.5 nuts.
Anz2.jpg


  • Step 3. Fixed the bracket holder to the fan with long steel screws and nuts.
Anz2 2.jpg


  • Step 4. Fixed other device as mentioned before, for example: 4 pieces of Raspberry Pi or other combinations.And then place them as following picture, please pay attention to the direction where there is a “R” mark. Connect the fan cable to Raspberry Pi on 5V and GND Pin.
Anz3.jpg


NOTE: Please beware of the direction of the acrylic holder.

Anz4.jpg


Caution: Incorrect polarity may cause damage to your device!

Anz5.jpg


  • Step 5. Place another pieces of acrylic layer on the top and fixed it with long steel screws.
Anz6.jpg


  • Step 6. Install acrylic crystal hander with M3x9mm screws.
Anz7.jpg


There are two popular solution for this case:

  • 1. Raspberry Pi smart NAS Cluster:
Anz8.jpg


  • 2. Jetson Nano AI Deep Learning (Machine Learning) Cluster storage.
Anz9.jpg


Keywords

  • Rack Tower, Acrylic case, Raspberry Pi 4B, Jetson Nano, Huge Fan, Heat dissipation, 52Pi

FAQ

  • Q: Dose it fit for Raspberry Pi Zero ?
 A: No, the mounting holes are fit for Raspberry Pi 4B /3B+ /3B and Jetson Nano.