EZ-0048
USB-Port-GPS Module
Description
- Support Raspberry Pi model A, B, A+, B+, Zero, 2, 3 with its' L80-39 GPS chip inside.
- Communicates satellite with UART or USB.
- CP2102 as USB to UART Bridge chip, stable and faster.
- The L80-39 with 66 search channels and 22 simultaneous tracking channels,it acquires and tracks satellites in the shortest time at Outdoor.
Attention This module is fit for outdoor operation. please put the Antana in the open air.
Compatibility List
- Compatibility
Platform | USB-Port-GPS Module | Notes |
---|---|---|
Raspberry Pi 3 Model B Plus | √ | |
Raspberry Pi zero | √ | |
Raspberry Pi zero W | √ | |
Raspberry Pi 3 Model B | √ | |
Raspberry Pi 2 Model B | √ | |
Raspberry Pi Model B+ | √ |
Feature
- -165 dBm sensitivity, 1Hz (Default), up to 5Hz, 66 channels
- At least 100mA current draw to startup.
- PPS output can be used to coordinate time with satellite.
- Internal patch antenna which works quite well when used outdoors SMA connector for external active antenna for when used indoors
- Fix status LED blinks to let you know when the GPS has determined the current coordinates
- EASY™, advanced AGPS technology without external memory
- Support time service application which can be achieved by PPS sync NMEA feature
- Built-in LNA for better sensitivity
- RTC battery-compatible
- 1x8 male headers, USB micro Interface
- includes CP2102 Module Serial Converter USB 2.0 To TTL UART
Document Download: File:Quectel L80-R GPS Specification V1.0.pdf
Parameters
Type | value |
---|---|
Satellites | 66 acquisition channels,
22 tracking channels |
Work Voltage | 4.5-5.5V |
Weight | 4.35g |
Maximum Current | 100mA MAX |
Work Temperature | -40~+85℃ |
scale | 16.6x26x18.6(mm) |
GPS | L80-M39 |
Patch Antenna Size | 15.0 x 15.0 x 4.0mm |
Position Accuracy | <2.5M CEP |
Velocity Accuracy | <1.0m/s |
Warm/cold start without ESEY | <35s |
Warm/cold start with ESEY | <15s |
Acquisition sensitivity | -148dBm |
Tracking sensitivity | -165dBm |
Update rate | 1Hz (Default)
up to 5Hz |
Baud Rate | 4800~115200 bps
9600bps default |
Protocols | NMEA 0183 |
Mount Cable | 1*8 Stacking Header
USB micro data cable |
Presentation
Package includes:
- 1x USB-Port-GPS(L80-39) module
- 1x USB data wire
How to wire it up
Uart Style:
Because of the Serial port issue of Raspberry Pi 3, Model B, it may cause unexpected problem, we suggest that you do not connect GPS module with Raspberry Pi directly with GPIO Pins.
- 1.You need a USB-to-TTL cable to connect GPS module and Raspberry Pi ,and you can wire it up like this chart:
GPS module | Wire color |
---|---|
VCC | Red wire |
GND | Black wire |
TXD | Green wire |
RXD | White wire |
- 2.Power on Raspberry Pi and login, open a terminal and type following commands if you use raspberry Pi in desktop environment.
USB Style:
- Just use a microUSB cable connect Raspberry Pi USB port with GPS module and power on Raspberry Pi.
|
How to use it
1. After power on and login to system. you can open a terminal and typing following command to install packages for GPS module.
sudo apt-get update && sudo apt-get -y install gpsd gpsd-clients python-gps
2.Start the gpsd service and control it.
Enable it:
sudo systemctl enable gpsd.socket
Start it:
sudo systemctl start gpsd.socket
Restart it:
sudo systemctl restart gpsd.socket
Check status:
sudo systemctl status gpsd.socket
4.Modify the configuration file of gpsd in /etc/default/gpsd
Modify the "DEVICE" parameter according to the name of serial port in /dev folder.
It is usually named "/dev/ttyUSB0" if you connect it to Raspberry Pi via USB cable.
You can use "nano" or "vim.tiny" editor to finish it.
Restart service:
sudo systemctl restart gpsd.socket
Finally, use this command to get information from GPS module.
sudo cgps -s
You will see this:
Trouble Shooting
If you can not get the information mentioned before.
You can use this command to check if serial is working properly.
cat /dev/ttyUSB0
it works fine if you see this picture:
FAQ
- Question: I use L80-39 GPS module. I choose to connect the GPS to the raspberry using a USB port. I followed these steps:
pi@raspberrypi ~ $ sudo cat /dev/ttyUSB0
$GPRMC,144034.00,V,,,,,,,090315,,,N*75
$GPVTG,,,,,,,,,N*30
$GPGGA,144034.00,,,,,0,00,99.99,,,,,,*60
$GPGSA,A,1,,,,,,,,,,,,,99.99,99.99,99.99*30
$GPGSV,1,1,01,15,,,25*7B
sudo apt-get update
sudo apt-get install gpsd gpsd-clients
sudo dpkg-reconfigure gpsd
start gpsd automatically: yes
Should gpsd handle attached USB receivers automatically: yes
Device the GPS receiver is attached to: <leave blank>
Options to gpsd: -n /dev/ttyUSB0
gpsd control socket path: <use default>
sudo gpsd /dev/ttyUSB0 -F /var/run/gpsd.sock
cgps -s
**NO FIX**
What should I do for NO FIX problem?
- Answer: You can modify /etc/defalut/gpsd file and make sure you input the right arguments as following picture:
- Question: Can I use it in my car as a GPS receiver ?
- Answer: please see this manual and try lcdgps command.
lcdgps
A client that passes gpsd data to lcdproc, turning your car computer into a very expensive and
nearly feature-free GPS receiver. Currently assumes a 4x40 LCD and writes data formatted to fit
that size screen. Also displays 4- or 6-character Maidenhead grid square output.
- Does it supports the entire NMEA Version 3 sentences or just a subset of it?
Answer: Yes, it is, Our GPS module support standard NMEA protocol, more information you can read this datasheet:
[L80 gps protocol specification v1.0.pdf | http://wiki.52pi.com/index.php/File:L80_gps_protocol_specification_v1.0.pdf]